Photocatalytic water splitting

Photocatalytic water splitting is a process that uses photocatalysis for the dissociation of water (H2O) into hydrogen (H
2
) and oxygen (O
2
). The inputs are light energy (photons), water, and a catalyst(s). The process is inspired by Photosynthesis, which converts water and carbon dioxide into oxygen and carbohydrates. Water splitting using solar radiation has not been commercialized.[1] Photocatalytic water splitting is done by dispersing photocatalyst particles in water or depositing them on a substrate, unlike Photoelectrochemical cell, which are assembled into a cell with a photoelectrode.[2] Hydrogen fuel production using water and light (photocatalytic water splitting), instead of petroleum, is an important renewable energy strategy.

Concepts

[edit]
Water splitting is driven by the electron-hole pair generated by a photon. The bandgap is the energy difference between the conduction band minimum (CB) and the valence band maximum (VB). Electrocatalysts are added to reduce the overpotential of water splitting

Two mole of H2O is split into 1 mole O
2
and 2 mole H
2
using light in the process shown below.

A photon with an energy greater than 1.23 eV is needed to generate an electron–hole pairs, which react with water on the surface of the photocatalyst. The photocatalyst must have a bandgap large enough to split water; in practice, losses from material internal resistance and the overpotential of the water splitting reaction increase the required bandgap energy to 1.6–2.4 eV to drive water splitting.[2]

The process of water-splitting is a highly endothermic process (ΔH > 0). Water splitting occurs naturally in photosynthesis when the energy of four photons is absorbed and converted into chemical energy through a complex biochemical pathway (Dolai's or Kok's S-state diagrams).[3]

O–H bond homolysis in water requires energy of 6.5 - 6.9 eV (UV photon).[4][5] Infrared light has sufficient energy to mediate water splitting because it technically has enough energy for the net reaction. However, it does not have enough energy to mediate the elementary reactions leading to the various intermediates involved in water splitting (this is why there is still water on Earth). Nature overcomes this challenge by absorbing four visible photons. In the laboratory, this challenge is typically overcome by coupling the hydrogen production reaction with a sacrificial reductant other than water.[6]

Materials used in photocatalytic water splitting fulfill the band requirements and typically have dopants and/or co-catalysts added to optimize their performance. A sample semiconductor with the proper band structure is titanium dioxide (TiO
2
) and is typically used with a co-catalyst such as platinum (Pt) to increase the rate of H
2
production.[7] A major problem in photocatalytic water splitting is photocatalyst decomposition and corrosion.[7]

Method of evaluation

[edit]

Photocatalysts must conform to several key principles in order to be considered effective at water splitting. A key principle is that H
2
and O
2
evolution should occur in a stoichiometric 2:1 ratio; significant deviation could be due to a flaw in the experimental setup and/or a side reaction, neither of which indicate a reliable photocatalyst for water splitting. The prime measure of photocatalyst effectiveness is quantum yield (QY), which is:

QY (%) = (Photochemical reaction rate) / (Photon absorption rate) × 100%[7]

To assist in comparison, the rate of gas evolution can also be used. A photocatalyst that has a high quantum yield and gives a high rate of gas evolution is a better catalyst.

The other important factor for a photocatalyst is the range of light that is effective for operation. For example, a photocatalyst is more desirable to use visible photons than UV photons.

Photocatalysts

[edit]

The efficiency of solar-to-hydrogen (STH) of photocatalytic water splitting, however, has remained very low.

Gallium-indium nitride

[edit]

A STH efficiency of 9.2% indium.[8]

NaTaO
3
:La

[edit]

NaTaO
3
:La yielded the highest water splitting rate of photocatalysts without using sacrificial reagents.[7] This ultraviolet-based photocatalyst was reported to show water splitting rates of 9.7 mmol/h and a quantum yield of 56%. The nanostep structure of the material promotes water splitting as edges functioned as H
2
production sites and the grooves functioned as O
2
production sites. Addition of NiO particles as co-catalysts assisted in H
2
production; this step used an impregnation method with an aqueous solution of Ni(NO
3
)
2
•6H
2
O
and evaporated the solution in the presence of the photocatalyst. NaTaO
3
has a conduction band higher than that of NiO, so photo-generated electrons are more easily transferred to the conduction band of NiO for H
2
evolution.[9]

K
3
Ta
3
B
2
O
12

[edit]

K
3
Ta
3
B
2
O
12
is another catalyst solely activated by UV and above light. It does not have the performance or quantum yield of NaTaO
3
:La. However, it can split water without the assistance of co-catalysts and gives a quantum yield of 6.5%, along with a water splitting rate of 1.21 mmol/h. This ability is due to the pillared structure of the photocatalyst, which involves TaO
6
pillars connected by BO
3
triangle units. Loading with NiO did not assist the photocatalyst due to the highly active H
2
evolution sites.[10]

(Ga
.82
Zn
.18
)(N
.82
O
.18
)

[edit]

(Ga
.82
Zn
.18
)(N
.82
O
.18
) had the highest quantum yield in visible light for visible light-based photocatalysts that do not utilize sacrificial reagents as of October 2008.[7] The photocatalyst featured a quantum yield of 5.9% and a water splitting rate of 0.4 mmol/h. Tuning the catalyst was done by increasing calcination temperatures for the final step in synthesizing the catalyst. Temperatures up to 600 °C helped to reduce the number of defects, while temperatures above 700 °C destroyed the local structure around zinc atoms and were thus undesirable. The treatment ultimately reduced the amount of surface Zn and O defects, which normally function as recombination sites, thus limiting photocatalytic activity. The catalyst was then loaded with Rh
2-y
Cr
y
O
3
at a rate of 2.5 wt% Rh and 2 wt% Cr for better performance.[11]

Molecular catalysts

[edit]

Proton reduction catalysts based on earth-abundant elements[12][13] carry out one side of the water-splitting half-reaction.

A mole of octahedral nickel(II) complex, [Ni(bztpen)]2+ (bztpen = N-benzyl-N,N’,N’-tris(pyridine-2-ylmethyl)ethylenediamine) produced 308,000 moles of hydrogen over 60 hours of electrolysis with an applied potential of -1.25 V vs. standard hydrogen electrode.[14]

Ru(II) with three 2,2'-bipyridine ligands is a common compound for photosensitization used for photocatalytic oxidative transformations like water splitting. However, the bipyridine degrades due to the strongly oxidative conditions which causes the concentration of Ru(bpy)32+ to diminish. Measurements of the degradation is difficult with UV-Vis spectroscopy but MALDI MS can be used instead.[15]

Cobalt-based photocatalysts have been reported,[16] including tris(bipyridine) cobalt(II), compounds of cobalt ligated to certain cyclic polyamines, and some cobaloximes.

In 2014 researchers announced an approach that connected a chromophore to part of a larger organic ring that surrounded a cobalt atom. The process is less efficient than a platinum catalyst although cobalt is less expensive, potentially reducing costs. The process uses one of two supramolecular assemblies based on Co(II)-templated coordination of Ru(bpy)+32 (bpy = 2,2′-bipyridyl) analogues as photosensitizers and electron donors to a cobaloxime macrocycle. The Co(II) centers of both assemblies are high spin, in contrast to most previously described cobaloximes. Transient absorption optical spectroscopies indicate that charge recombination occurs through multiple ligand states within the photosensitizer modules.[17][18]

Bismuth vanadate

[edit]

Bismuth vanadate is a visible-light-driven photocatalyst with a bandgap of 2.4 eV.[19][20] BV have demonstrated efficiencies of 5.2% for flat thin films[21][22] and 8.2% for core-shell WO3@BiVO4 nanorods with thin absorbers.[23][24][25]

Bismuth oxides

[edit]

Bismuth oxides are characterized by visible light absorption properties, just like vanadates.[26][27]

Tungsten diselenide (WSe2)

[edit]

Tungsten diselenide has photocatalytic properties that might be a key to more efficient electrolysis.[28]

III-V semiconductor systems

[edit]

Systems based on III-V semiconductors, such as InGaP, enable solar-to-hydrogen efficiencies of up to 14%.[29] Challenges include long-term stability and cost.

2D semiconductor systems

[edit]

2-dimensional semiconductors such as MoS
2
are actively researched as potential photocatalysts.[30][31]

Aluminum‐based metal-organic frameworks

[edit]

An aluminum‐based metal-organic framework made from 2‐aminoterephthalate can be modified by incorporating Ni2+ cations into the pores through coordination with the amino groups.[32]Molybdenum disulfide

Porous organic polymers

[edit]

Organic semiconductor photocatalysts, in particular porous organic polymers (POPs), attracted attention due to their low cost, low toxicity, and tunable light absorption vs inorganic counterparts.[33][34][35] They display high porosity, low density, diverse composition, facile functionalization, high chemical/thermal stability, as well as high surface areas.[36] Efficient conversion of hydrophobic polymers into hydrophilic polymer nano-dots (Pdots) increased polymer-water interfacial contact, which significantly improved performance.[37][38][39]

Ansa-Titanocene(III/IV) Triflate Complexes

[edit]

Beweries, et al., developed a light-driven "closed cycle of water splitting using ansa-titanocene(III/IV) triflate complexes".[40]

Indium gallium nitride

[edit]

An Indium gallium nitride (InxGa1-xN) photocatalyst achieved a solar-to-hydrogen efficiency of 9.2% from pure water and concentrated sunlight. The effiency is due to the synergistic effects of promoting hydrogen–oxygen evolution and inhibiting recombination by operating at an optimal reaction temperature (~70 degrees C), powered by harvesting previously wasted infrared light. An STH efficiency of about 7% was realized from tap water and seawater and efficiency of 6.2% in a larger-scale system with a solar light capacity of 257 watts.[41]

Sacrificial reagents

[edit]

Cd
1-x
Zn
x
S

[edit]

Solid solutions Cd
1-x
Zn
x
S
with different Zn concentration (0.2 < x < 0.35) have been investigated in the production of hydrogen from aqueous solutions containing as sacrificial reagents under visible light.[42] Textural, structural and surface catalyst properties were determined by N
2
adsorption isotherms, UV–vis spectroscopy, SEM and XRD and related to the activity results in hydrogen production from water splitting under visible light. It was reported that the crystallinity and energy band structure of the Cd
1-x
Zn
x
S
solid solutions depend on their Zn atomic concentration. The hydrogen production rate increased gradually as Zn concentration on photocatalysts increased from 0.2 to 0.3. The subsequent increase in the Zn fraction up to 0.35 reduced production. Variation in photoactivity was analyzed for changes in crystallinity, level of the conduction band and light absorption ability of Cd
1-x
Zn
x
S
solid solutions derived from their Zn atomic concentration.

Further reading

[edit]
  • Chu, Sheng; Li, Wei; Hamann, Thomas; Shih, Ishiang; Wang, Dunwei; Mi, Zetian (2017). "Roadmap on solar water splitting: current status and future prospects". Nano Futures. 1 (2): 022001. Bibcode:2017NanoF...1b2001C. doi:10.1088/2399-1984/aa88a1. S2CID 3903962.
  • Takata, Tsuyoshi; Jiang, Junzhe; Sakata, Yoshihisa; Nakabayashi, Mamiko; Shibata, Naoya; Nandal, Vikas; Seki, Kazuhiko; Hisatomi, Takashi; Domen, Kazunari (2020-05-28). "Photocatalytic water splitting with a quantum efficiency of almost unity". Nature. 581 (7809): 411–414. Bibcode:2020Natur.581..411T. doi:10.1038/s41586-020-2278-9. ISSN 0028-0836. PMID 32461647. S2CID 218912943.
  • del Valle, F.; Álvarez Galván, M. Consuelo; Del Valle, F.; Villoria De La Mano, José A.; Fierro, José L. G.; et al. (Jun 2009). "Water Splitting on Semiconductor Catalysts under Visible-Light Irradiation". ChemSusChem. 2 (6): 471–485. doi:10.1002/cssc.200900018. PMID 19536754.
  • del Valle, F.; Del Valle, F.; Villoria De La Mano, J.A.; Álvarez-Galván, M.C.; Fierro, J.L.G.; et al. (2009). "Advances in Chemical Engineering". Photocatalytic water splitting under visible Light: concept and materials requirements. Vol. 36. pp. 111–143. doi:10.1016/S0065-2377(09)00404-9. ISBN 9780123747631.

See also

[edit]

References

[edit]
  1. ^ Kudo, Akihiko; Miseki, Yugo (2009). "Heterogeneous photocatalyst materials for water splitting". Chem. Soc. Rev. 38 (1): 253–278. doi:10.1039/b800489g. PMID 19088977.
  2. ^ a b Kim, Jin Hyun; Hansora, Dharmesh; Sharma, Pankaj; Jang, Ji-Wook; Lee, Jae Sung (2019). "Toward practical solar hydrogen production – an artificial photosynthetic leaf-to-farm challenge". Chemical Society Reviews. 48 (7): 1908–1971. doi:10.1039/c8cs00699g. PMID 30855624.
  3. ^ Yano, Junko; Yachandra, Vittal (2014-04-23). "Mn 4 Ca Cluster in Photosynthesis: Where and How Water is Oxidized to Dioxygen". Chemical Reviews. 114 (8): 4175–4205. doi:10.1021/cr4004874. ISSN 0009-2665. PMC 4002066. PMID 24684576.
  4. ^ Gligorovski, Sasho; Strekowski, Rafal; Barbati, Stephane; Vione, Davide (2015-12-23). "Environmental Implications of Hydroxyl Radicals ( • OH)". Chemical Reviews. 115 (24): 13051–13092. doi:10.1021/cr500310b. ISSN 0009-2665. PMID 26630000.
  5. ^ Fujishima, Akira (13 September 1971). "Electrochemical Photolysis of Water at a Semiconductor Electrode". Nature. 238 (5358): 37–38. Bibcode:1972Natur.238...37F. doi:10.1038/238037a0. PMID 12635268. S2CID 4251015.
  6. ^ Zhou, Dantong; Li, Dongxiang; Yuan, Shengpeng; Chen, Zhi (2022-08-25). "Recent Advances in Biomass-Based Photocatalytic H 2 Production and Efficient Photocatalysts: A Review". Energy & Fuels. 36 (18): 10721–10731. doi:10.1021/acs.energyfuels.2c01904. ISSN 0887-0624. S2CID 251852086.
  7. ^ a b c d e Kudo, A.; Miseki, Y. (2009). "Heterogeneous photocatalyst materials for water splitting". Chem. Soc. Rev. 38 (1): 253–278. doi:10.1039/b800489g. PMID 19088977.
  8. ^ Zhou, Peng; Navid, Ishtiaque Ahmed; Ma, Yongjin; Xiao, Yixin; Wang, Ping; Ye, Zhengwei; Zhou, Baowen; Sun, Kai; Mi, Zetian (January 2023). "Solar-to-hydrogen efficiency of more than 9% in photocatalytic water splitting". Nature. 613 (7942): 66–70. Bibcode:2023Natur.613...66Z. doi:10.1038/s41586-022-05399-1. PMID 36600066.
  9. ^ Kato, H.; Asakura, K.; Kudo, A. (2003). "Highly Efficient Water Splitting into H and O over Lanthanum-Doped NaTaO Photocatalysts with High Crystallinity and Surface Nanostructure". J. Am. Chem. Soc. 125 (10): 3082–3089. doi:10.1021/ja027751g. PMID 12617675.
  10. ^ T. Kurihara, H. Okutomi, Y. Miseki, H. Kato, A. Kudo, "Highly Efficient Water Splitting over K
    3
    Ta
    3
    B
    2
    O
    12
    Photocatalyst without Loading Cocatalyst" Chem. Lett., 35, 274 (2006).
  11. ^ K. Maeda, K. Teramura, K. Domen, "Effect of post-calcination on photocatalytic activity of (Ga
    1-x
    Zn
    x
    )(N
    1-x
    O
    x
    ) solid solution for overall water splitting under visible light" J. Catal., 254, 198 (2008).
  12. ^ McKone, James R.; Marinescu, Smaranda C.; Brunschwig, Bruce S.; Winkler, Jay R.; Gray, Harry B. (2014). "Earth-abundant hydrogen evolution electrocatalysts". Chem. Sci. 5 (3): 865–878. doi:10.1039/C3SC51711J. ISSN 2041-6520.
  13. ^ Sutra, P.; Igau, A. (April 2018). "Emerging Earth-abundant (Fe, Co, Ni, Cu) molecular complexes for solar fuel catalysis". Current Opinion in Green and Sustainable Chemistry. 10: 60–67. doi:10.1016/j.cogsc.2018.03.004.
  14. ^ Zhang, Peili; Wang, Mei; Yang, Yong; Zheng, Dehua; Han, Kai; Sun, Licheng (2014). "Highly efficient molecular nickel catalysts for electrochemical hydrogen production from neutral water". Chem. Commun. 50 (91): 14153–14156. doi:10.1039/C4CC05511J. ISSN 1359-7345. PMID 25277377.
  15. ^ Bergman, Nina; Thapper, Anders; Styring, Stenbjörn; Bergquist, Jonas; Shevchenko, Denys (2014). "Quantitative determination of the Ru(bpy) 3 2+ cation in photochemical reactions by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry". Anal. Methods. 6 (21): 8513–8518. doi:10.1039/C4AY01379D. ISSN 1759-9660.
  16. ^ Artero, V.; Chavarot-Kerlidou, M.; Fontecave, M. (2011). "Splitting Water with Cobalt". Angewandte Chemie International Edition. 50 (32): 7238–7266. doi:10.1002/anie.201007987. PMID 21748828.
  17. ^ Mukherjee, Anusree; Kokhan, Oleksandr; Huang, Jier; Niklas, Jens; Chen, Lin X.; Tiede, David M.; Mulfort, Karen L. (2013). "A less-expensive way to duplicate the complicated steps of photosynthesis in making fuel". Physical Chemistry Chemical Physics. 15 (48): 21070–6. Bibcode:2013PCCP...1521070M. doi:10.1039/C3CP54420F. PMID 24220293. Retrieved 2014-01-23.
  18. ^ Mukherjee, A.; Kokhan, O.; Huang, J.; Niklas, J.; Chen, L. X.; Tiede, D. M.; Mulfort, K. L. (2013). "Detection of a charge-separated catalyst precursor state in a linked photosensitizer-catalyst assembly". Physical Chemistry Chemical Physics. 15 (48): 21070–21076. Bibcode:2013PCCP...1521070M. doi:10.1039/C3CP54420F. PMID 24220293.
  19. ^ Shafiq, Iqrash; Hussain, Murid; Shehzad, Nasir; Maafa, Ibrahim M.; Akhter, Parveen; Amjad, Um-e-salma; Shafique, Sumeer; Razzaq, Abdul; Yang, Wenshu; Tahir, Muhammad; Russo, Nunzio (August 2019). "The effect of crystal facets and induced porosity on the performance of monoclinic BiVO4 for the enhanced visible-light driven photocatalytic abatement of methylene blue". Journal of Environmental Chemical Engineering. 7 (4): 103265. doi:10.1016/j.jece.2019.103265. ISSN 2213-3437. S2CID 198742844.
  20. ^ Shafiq, I. (2018). Mesoporous monoclinic BiVO4 for efficient visible light driven photocatalytic degradation of dyes (Doctoral dissertation, COMSATS University Islamabad, Lahore Campus.).
  21. ^ Abdi, Fatwa F; Lihao Han; Arno H. M. Smets; Miro Zeman; Bernard Dam; Roel van de Krol (29 July 2013). "Efficient solar water splitting by enhanced charge separation in a bismuth vanadate-silicon tandem photoelectrode". Nature Communications. 4: 2195. Bibcode:2013NatCo...4.2195A. doi:10.1038/ncomms3195. PMID 23893238.
  22. ^ Han, Lihao; Abdi, Fatwa F.; van de Krol, Roel; Liu, Rui; Huang, Zhuangqun; Lewerenz, Hans-Joachim; Dam, Bernard; Zeman, Miro; Smets, Arno H. M. (2014). "Inside Cover: Efficient Water-Splitting Device Based on a Bismuth Vanadate Photoanode and Thin-Film Silicon Solar Cells (ChemSusChem 10/2014)". ChemSusChem. 7 (10): 2758. doi:10.1002/cssc.201402901.
  23. ^ Pihosh, Yuriy; Turkevych, Ivan; Mawatari, Kazuma; Uemura, Jin; Kazoe, Yutaka; Kosar, Sonya; Makita, Kikuo; Sugaya, Takeyoshi; Matsui, Takuya; Fujita, Daisuke; Tosa, Masahiro (2015-06-08). "Photocatalytic generation of hydrogen by core-shell WO 3 /BiVO 4 nanorods with ultimate water splitting efficiency". Scientific Reports. 5 (1): 11141. Bibcode:2015NatSR...511141P. doi:10.1038/srep11141. ISSN 2045-2322. PMC 4459147. PMID 26053164.
  24. ^ Kosar, Sonya; Pihosh, Yuriy; Turkevych, Ivan; Mawatari, Kazuma; Uemura, Jin; Kazoe, Yutaka; Makita, Kikuo; Sugaya, Takeyoshi; Matsui, Takuya; Fujita, Daisuke; Tosa, Masahiro (2016-02-25). "Tandem photovoltaic–photoelectrochemical GaAs/InGaAsP–WO3/BiVO4device for solar hydrogen generation". Japanese Journal of Applied Physics. 55 (4S): 04ES01. Bibcode:2016JaJAP..55dES01K. doi:10.7567/jjap.55.04es01. ISSN 0021-4922. S2CID 125395272.
  25. ^ Kosar, Sonya; Pihosh, Yuriy; Bekarevich, Raman; Mitsuishi, Kazutaka; Mawatari, Kazuma; Kazoe, Yutaka; Kitamori, Takehiko; Tosa, Masahiro; Tarasov, Alexey B.; Goodilin, Eugene A.; Struk, Yaroslav M. (2019-07-01). "Highly efficient photocatalytic conversion of solar energy to hydrogen by WO3/BiVO4 core–shell heterojunction nanorods". Applied Nanoscience. 9 (5): 1017–1024. Bibcode:2019ApNan...9.1017K. doi:10.1007/s13204-018-0759-z. ISSN 2190-5517. S2CID 139703154.
  26. ^ Ropero-Vega, J.L.; Pedraza-Avella, J.A.; Niño-Gómez, M.E. (September 2015). "Hydrogen production by photoelectrolysis of aqueous solutions of phenol using mixed oxide semiconductor films of Bi–Nb–M–O (M=Al, Fe, Ga, In) as photoanodes". Catalysis Today. 252: 150–156. doi:10.1016/j.cattod.2014.11.007.
  27. ^ Ropero-Vega, J. L.; Meléndez, A. M.; Pedraza-Avella, J. A.; Candal, Roberto J.; Niño-Gómez, M. E. (July 2014). "Mixed oxide semiconductors based on bismuth for photoelectrochemical applications". Journal of Solid State Electrochemistry. 18 (7): 1963–1971. doi:10.1007/s10008-014-2420-4. hdl:11336/31744. ISSN 1432-8488. S2CID 95775856.
  28. ^ "Discovery Brightens Solar's Future, Energy Costs to Be Cut". NBC News. NBC News from Reuters. July 2, 2015. Retrieved July 2, 2015.
  29. ^ May, Matthias M; Hans-Joachim Lewerenz; David Lackner; Frank Dimroth; Thomas Hannappel (15 September 2015). "Efficient direct solar-to-hydrogen conversion by in situ interface transformation of a tandem structure". Nature Communications. 6: 8286. arXiv:1508.01666. Bibcode:2015NatCo...6.8286M. doi:10.1038/ncomms9286. PMC 4579846. PMID 26369620.
  30. ^ Luo, Bin; Liu, Gang; Wang, Lianzhou (2016). "Recent advances in 2D materials for photocatalysis". Nanoscale. 8 (13): 6904–6920. Bibcode:2016Nanos...8.6904L. doi:10.1039/C6NR00546B. ISSN 2040-3364. PMID 26961514.
  31. ^ Li, Yunguo; Li, Yan-Ling; Sa, Baisheng; Ahuja, Rajeev (2017). "Review of two-dimensional materials for photocatalytic water splitting from a theoretical perspective". Catalysis Science & Technology. 7 (3): 545–559. doi:10.1039/C6CY02178F. ISSN 2044-4753.
  32. ^ "Ni(2) Coordination to an Al‐Based Metal–Organic Framework Made from 2‐Aminoterephthalate for Photocatalytic Overall Water Splitting". Angewandte Chemie International Edition. 56 (11): 3036–3040. February 7, 2017. doi:10.1002/anie.201612423. PMID 28170148.
  33. ^ Kalsin, A. M.; Fialkowski, M.; Paszewski, M.; Smoukov, S. K.; Bishop, K. J. M.; Grzybowski, B. A. (2006-04-21). "Electrostatic Self-Assembly of Binary Nanoparticle Crystals with a Diamond-Like Lattice". Science. 312 (5772): 420–424. Bibcode:2006Sci...312..420K. doi:10.1126/science.1125124. ISSN 0036-8075. PMID 16497885.
  34. ^ Martin, David James; Reardon, Philip James Thomas; Moniz, Savio J. A.; Tang, Junwang (2014-09-10). "Visible Light-Driven Pure Water Splitting by a Nature-Inspired Organic Semiconductor-Based System". Journal of the American Chemical Society. 136 (36): 12568–12571. doi:10.1021/ja506386e. ISSN 0002-7863. PMID 25136991.
  35. ^ Weingarten, Adam S.; Kazantsev, Roman V.; Palmer, Liam C.; Fairfield, Daniel J.; Koltonow, Andrew R.; Stupp, Samuel I. (2015-12-09). "Supramolecular Packing Controls H2 Photocatalysis in Chromophore Amphiphile Hydrogels". Journal of the American Chemical Society. 137 (48): 15241–15246. doi:10.1021/jacs.5b10027. ISSN 0002-7863. PMC 4676032. PMID 26593389.
  36. ^ Zhang, Ting; Xing, Guolong; Chen, Weiben; Chen, Long (2020-02-07). "Porous organic polymers: a promising platform for efficient photocatalysis". Materials Chemistry Frontiers. 4 (2): 332–353. doi:10.1039/C9QM00633H. ISSN 2052-1537.
  37. ^ Wang, Lei; Fernández‐Terán, Ricardo; Zhang, Lei; Fernandes, Daniel L. A.; Tian, Lei; Chen, Hong; Tian, Haining (2016). "Organic Polymer Dots as Photocatalysts for Visible Light-Driven Hydrogen Generation". Angewandte Chemie International Edition. 55 (40): 12306–12310. doi:10.1002/anie.201607018. ISSN 1521-3773. PMID 27604393.
  38. ^ Pati, Palas Baran; Damas, Giane; Tian, Lei; Fernandes, Daniel L. A.; Zhang, Lei; Pehlivan, Ilknur Bayrak; Edvinsson, Tomas; Araujo, C. Moyses; Tian, Haining (2017-06-14). "An experimental and theoretical study of an efficient polymer nano-photocatalyst for hydrogen evolution". Energy & Environmental Science. 10 (6): 1372–1376. doi:10.1039/C7EE00751E. ISSN 1754-5706.
  39. ^ Rahman, Mohammad; Tian, Haining; Edvinsson, Tomas (2020). "Revisiting the Limiting Factors for Overall Water-Splitting on Organic Photocatalysts". Angewandte Chemie International Edition. 59 (38): 16278–16293. doi:10.1002/anie.202002561. ISSN 1521-3773. PMC 7540687. PMID 32329950.
  40. ^ Godemann, Christian; Hollmann, Dirk; Kessler, Monty; Jiao, Haijun; Spannenberg, Anke; Brückner, Angelika; Beweries, Torsten (2015-12-30). "A Model of a Closed Cycle of Water Splitting Using ansa -Titanocene(III/IV) Triflate Complexes". Journal of the American Chemical Society. 137 (51): 16187–16195. doi:10.1021/jacs.5b11365. ISSN 0002-7863. PMID 26641723.
  41. ^ Zhou, Peng; Navid, Ishtiaque Ahmed; Ma, Yongjin; Xiao, Yixin; Wang, Ping; Ye, Zhengwei; Zhou, Baowen; Sun, Kai; Mi, Zetian (January 2023). "Solar-to-hydrogen efficiency of more than 9% in photocatalytic water splitting". Nature. 613 (7942): 66–70. Bibcode:2023Natur.613...66Z. doi:10.1038/s41586-022-05399-1. ISSN 1476-4687. PMID 36600066. S2CID 255474993.
  42. ^ del Valle, F.; Ishikawa, A.; Domen, K.; Villoria De La Mano, J.A.; Sánchez-Sánchez, M.C.; González, I.D.; Herreras, S.; Mota, N.; Rivas, M.E. (May 2009). "Influence of Zn concentration in the activity of Cd1-xZnxS solid solutions for water splitting under visible light". Catalysis Today. 143 (1–2): 51–59. doi:10.1016/j.cattod.2008.09.024.